Art.-No. 500573

fischer Nail anchor FNA II 6 x 30/75 HCR with nail head highly corrosion-resistant steel

Top Features

Hammerset installation saves time.
No reinforcement hits due to low anchorage depth This saves time and costs during series installation.
Expansion clip provides a firm hold.
ETA approval for multiple fixings.
Made of highly corrosion-resistant steel for highly-corrosive atmospheres.

The installation-friendly Hammerset anchor for multiple fixings

Advantages

The special active principle allows for a simple hammerset installation and, therefore, a short processing time.
The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation.
The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations.
The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.
A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use.

The fischer nail anchor FNA II with nail head is made of highly corrosion-resistant steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with nail head is suitable for fixing fire protection boards, air lines and and mounting rails in highly corrosive atmospheres.

Applications

Fire protection plates
Fire protection boards
Ventilation systems
Wire and nonious hangers
Mounting rails
Metal clamps
Substructures made of wood and metal

Building materials

Approved for:

Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications

Also suitable for:

Solid sand-lime brick
Natural stone with dense structure
Prestressed hollow-core concrete slabs

Podroben opis najdete v priloženem dokumentu

Dovoljenja

ETA-06/0175
DoP No. 0235
GS 6.1/21-076-1

Functionality

The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and H
are suitable for pre-positioned installation.
The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall.
Available setting tools:
FNA S-SBO to slip onto the drill,
FNA S-SDS for series installation with a drilling hammer,
FNA S-H for the manual installation of mounting rails.

Mounting Strip 1 Picture

1 / 4

ETA Certification Document

pdf, ETA-06/0175

European Technical Assessment for fischer Nail anchor FNA II - Load controlled expansion anchor for multiple use for non-structural applications in concrete

Ustvarjeno na 02. 03. 2021

DOP - Declaration of Performance

pdf, DoP No. 0235

Declaration of Performance for fischer Nail anchor FNA II (Mechanical fastener for use in concrete)

Ustvarjeno na 16. 03. 2021

Test report (fire protection)

pdf, GS 6.1/21-076-1

Assessment of the load-bearing behaviour of ﬁscher nail anchors FNA II R and FNA II HCR under tension load and one-sided ﬁre loading according to the ZTV-ING-curve

Ustvarjeno na 05. 10. 2021

Load Table

pdf,

Nail anchor FNA II - Permissible loads for a single anchor for multiple use of redundant non-structural applications in normal concrete C20/25 up to C50/60.

ETA-approval
Anchor length ( l )	112,5 mm
Drill diameter ( d₀ )	6 mm
Min. drill hole depth for through fixings ( h₂ )	115 mm
Max. fixture thickness ( t _fix )	75 mm
Head-ø ( d_h )	13 mm
Packaging	Folding box
Amount	50 pcs.
GTIN (EAN-Code)	4048962001211

fischer Nail anchor FNA II 6 x 30/75 HCR with nail head highly corrosion-resistant steel

Opis izdelka

Dovoljenje aplikaciji

Navodila uporabe

Tehnični podatki

Dokumenti za prenos